M-Cool is a innovative acrylic-based, newly designed, special additives enhanced, ready-to-use flexible, sunlight reflection & thermal insulation coating which reduces the room temperature up to 7 – 9°C at peak summer hours.
| Properties | Specifications |
|---|---|
| Appearance | White, smooth paste |
| Brookfield viscosity | 8000 ± 1000 cP |
| Specific gravity @ 27°C | 1.00 ± 0.05 |
| Non-volatile content | 60 ± 3% |
| pH | 8.00 – 10.00 |
| Surface dry | 30 minutes |
| DFT per coat | 80 – 90 microns |
| Over coating interval | 2-4 hours |
- Asbestos, non-asbestos, sunshades, RCC, cement sheets
- Terraces, rooftops, parapet walls, lime terraced roofs, roof slabs
- Exterior & Interior walls of buildings
- Ideal for R.C.C., asbestos, aon-asbestos, Cement sheets, etc
- Reduces power and water consumption of humidification plants
- Highly flexible film
- Water vapour permeable (breathable)
- Crack bridging
- Prevents fungal & algae growth
- Environment friendly
- Best before 12 months in an unopened, undamaged, originally sealed packing and if stored in dry conditions
- Protect from direct sunlight
135 – 150 sq.ft / litre / coat.
- All surfaces must be clean, dry and free of dirt, chalk, grease, oil, wax, rust and loose or peeling paint before painting
- Repair holes and cracks with Vijay Crack-X and prime the surface using M-Cool Primer in 1:1 ratio with water by brush or spray
- Dilute with 40 - 50% of water by volume to M-Cool and stir thoroughly to get a homogenous mixture
- Apply single coat by brush or spray and allow it to dry for about 2-4 hours
- After 2-4 hours, apply second coat by brush or spray
- Do not apply in hot sunlight.
- Primer and two coats are mandatory for durability of coating.
- Use rubber hand gloves & safety goggles
- In case of contact with skin, wash with plenty of water
- Keep out of reach of children
| Properties | Specifications |
|---|---|
| Appearance | White, smooth paste |
| Brookfield viscosity | 8000 ± 1000 cP |
| Specific gravity @ 27°C | 1.00 ± 0.05 |
| Non-volatile content | 60 ± 3% |
| pH | 8.00 – 10.00 |
| Surface dry | 30 minutes |
| DFT per coat | 80 – 90 microns |
| Over coating interval | 2-4 hours |
- Asbestos, non-asbestos, sunshades, RCC, cement sheets
- Terraces, rooftops, parapet walls, lime terraced roofs, roof slabs
- Exterior & Interior walls of buildings
- Ideal for R.C.C., asbestos, aon-asbestos, Cement sheets, etc
- Reduces power and water consumption of humidification plants
- Highly flexible film
- Water vapour permeable (breathable)
- Crack bridging
- Prevents fungal & algae growth
- Environment friendly
- Best before 12 months in an unopened, undamaged, originally sealed packing and if stored in dry conditions
- Protect from direct sunlight
135 – 150 sq.ft / litre / coat.
- All surfaces must be clean, dry and free of dirt, chalk, grease, oil, wax, rust and loose or peeling paint before painting
- Repair holes and cracks with Vijay Crack-X and prime the surface using M-Cool Primer in 1:1 ratio with water by brush or spray
- Dilute with 40 - 50% of water by volume to M-Cool and stir thoroughly to get a homogenous mixture
- Apply single coat by brush or spray and allow it to dry for about 2-4 hours
- After 2-4 hours, apply second coat by brush or spray
- Do not apply in hot sunlight.
- Primer and two coats are mandatory for durability of coating.
- Use rubber hand gloves & safety goggles
- In case of contact with skin, wash with plenty of water
- Keep out of reach of children